GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. 1068 SECTION ENGINE Item# List 957-MSS 771.83 EA Allows you to remove your motor from your dinghy and place it on the swim platform in a horizontal position before getting out of your dinghy. The bracket is removable from the swim step leaving a low profile receiver plate on the swim platform similar to the Weaver Quick Kit bracket. Dimensions 13" W x 5" D x 10" H. MOTOSTO SWIM PLATFORM Item# List 957-MST 971.49 EA Allows you to store your 15 hp or smaller on the transom of your yacht. When under way the bracket is in normal position and when using the motor the bracket can be swung out of the way against the transom. This bracket is not removable. MOTOSTO TRANSOM MOUNT Item# List 299-60326 126.99 EA For Motors up to 12 HP. Fits 7/ 8" or 1" railings. TEAK OUTBOARD MOUNTING BRACKET Adjustable O.B. motor bracket features a stainless bracket for years of dependable fresh or saltwater operation. 8.1/ 2" x 101/ 2" mounting pad. For 2-Stroke motors only, Not recommended for 4-Stroke outboards. By MarineTech TM STAINLESS STEEL 2-STROKE OUTBOARD MOTOR BRACKET Item# HP Max Load Vertical Travel List 781-550010 Up to 10 80 lbs. 14" 334.29 EA Item# Max Load Rating Vertical Travel Type List 781-550407AL 132 lb. 15 hp 10"-4 Positions Aluminum 652.39 EA 781-550408SS 132 lb. 15-20hp 11"-5 Positions Stainless Steel 761.59 EA Adjustable, heavy duty outboard motor brackets are built to handle the increased torque of today's motors. They will handle 4-stroke motors up to 15hp or 2-stroke motors up to 20hp. Features Twist-knob safety locks, heavy-duty stainless steel torsion springs for easy lifting, and stainless steel hardware. The 2" thick, extra wide, maintenance free polypropylene mounting board will handle just about any motor. Multi-position lock bar allows for installation flexibility for either long or short shaft motors. By MarineTech TM 4-STROKE/2-STROKE OUTBOARD MOTOR BRACKET 550407AL 550408SS Item# HP Max Load Vertical Travel List 781-550410 Up to 35 263 lbs 10"-5 Positions 697.99 EA 781-550416 Up to 35 263 lbs 16"-4 Positions 905.79 EA The black anodized aluminum bracket is built to handle the increased weight and torque of today's 4-strokes with long or short shafts. Hand-adjustable with just the turn of a knob, stainless steel torsion springs counterbalance motor weight. The 2" thick polypropylene mounting board, along with aircraft-type stainless steel hardware deliver heavy-duty performance. Motor safety cable is included. By MarineTech TM ALUMINUM 4-STROKE OUTBOARD MOTOR BRACKET 550410 550416 RAIL MOUNT MOTOR BRACKET Item# Rating Color A B C List 354-327151 8 HP (2-Cycle Only) Black 19/ 16" 611/ 16" 611/ 16" 49.59 EA 354-327150 8 HP (2-Cycle Only) White 19/ 16" 611/ 16" 611/ 16" 48.23 EA 354-3271501 8 HP (2-Cycle Only) White 19/ 16" 611/ 16" 611/ 16" 53.32 EA Designed to hold small 2-cycle outboards up to 8 HP upright on the stern rail. Will fit both 7/ 8" and 1" rails, as well as rails using 90° tee fittings. The two-piece unit is made of UV stabilized polypropylene and comes complete with fasteners. Can also be used as a mounting platform for barbecues, down rigger brackets, fish cleaning tables, etc. Item# List 957-MOTOKR8 545.25 EA This trolling motor fixed bracket is designed to install on a swim platform. It will hold up to a 9.9 hp 4 stroke engine. Made for the marine enviroment from 304 SS with welded seams. The mounting pad is made from Starboard. Bracket dimensions 11.25"W x 5"D (+1.5" Pad) x 8"H. WEAVER MOTO KICKER
RkJQdWJsaXNoZXIy MTI2MTky