GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEM NUMBERS IN RED ARE HAZARDOUS ITEMS IN BLUE ARE NEW ] SEA VALUE v OVERSIZED dCOURIER SURCHARGE SECTION 369 ANCHORING/MOORING Use to cover raw leg pipe edges. Gives dock the finishing touch. 4-Pack. PLASTIC LEG CAPS FOR STATIONARY DOCKS Item# List 686-91111F 10.49 EA Item# List 686-92104F 27.99 EA For lighter duty applications where an outside corner is not necessary. INSIDE CORNER FOR FLOATING DOCKS Item# List 686-92116F 35.79 EA Use as inside corner. Adds extra strength with its' anchor chain bar. Accepts chain up to 1/ 2". INSIDE ANCHOR CORNER FOR FLOATING DOCKS Item# List 686-93122F 11.19 EA Used to sandwich wood framing when another piece of hardware isn't used. Prevents bolt loosening or pull-thru. BACKER PLATE FOR FLOATING DOCKS Item# List 686-96111F 14.99 EA Used to join male and female connectors. CONNECTOR PIN FOR FLOATING DOCKS Item# List 686-99001F 53.59 EA Maximum corner strength when used with 99004F Outside Corner or any Corner Connecting Hinge. Accepts chain up to 1/ 2". HD ANCHOR CHAIN CORNER FOR FLOATING DOCKS Item# List 686-99004F 44.99 EA Use with backer plates or inside corners at outside ends of docks, fingers and swim platforms. Use with backer plates or inside corners at outside ends of dock. OUTSIDE CORNER FOR FLOATING DOCKS Item# List 686-99006F 7.79 EA WASHER PLATE FOR FLOATING DOCKS Item# List 686-99009F 63.39 EA Can be used with all styles of Female Connector Hinges. MALE CORNER HINGE FOR FLOATING DOCKS Item# List 686-99010F 68.49 EA Can be used with all styles of Male Corner Hinge. FEMALE CORNER HINGE FOR FLOATING DOCKS Item# List 686-99011F 31.39 EA Can be used with all styles of Male Connector Hinges. FEMALE T CONNECTOR FOR FLOATING DOCKS Item# List 686-99012F 24.39 EA Can be used with all styles of Female Connector Hinges. MALE T CONNECTOR FOR FLOATING DOCKS Item# List 686-99013F 51.79 EA Holds chain up to 1/ 2" to secure the dock in place. CHAIN RETAINER FOR FLOATING DOCKS Item# Size List 686-90024F 24" Dia. x 8" W 107.99 EA For use at roll-in docks or boat lifts, this tough, rigid wheel offers stress, crack and impact resistance. At 24" (61,0cm) in diameter and an 800lb (362,9kg) capacity per wheel, it rolls easily over virtually any terrain and will not rust on the axle. Wheel accepts a 17/ 8" (4,8cm) O.D. axle. HEAVY DUTY 24" DOCK ROLLING WHEEL Item# Description List 241-26521 Standard Grade 67.82 EA 241-26400 Commercial Grade 80.48 EA A. Two 1/ 2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H. A. OUTSIDE CORNER (FEMALE) B. Use with a female outside corner to connect docks end to end. Joint requires 3/ 4" bolt set (N) or connector pin (O). Each leg is 10"L x 5" H. B. OUTSIDE CORNER (MALE) Item# Description Size List 241-26522 Standard Grade 1/ 2" Welded Tab 60.91 EA 241-25491 Commercial Grade 1/ 2" Welded Tab 65.22 EA 1/ 8" hot-dip galvanized steel. 7/ 16" holes for 3/ 8" carriage bolts. Bolts included are stainless steel. Large surface area is used in soft bottom areas. Leg pipe can extend through the pad into lake bottom for extra lateral support. Pointed corners grab when the bottom is rocky. Pipe above pad: 23/ 8" H and pipe below pad: 11/ 2"H STATIONARY DOCK HARDWARE Item# Size Pipe List 686-94102F 11" L x 11" W x 21/ 2" H 21/ 4" ID 50.39 EA
RkJQdWJsaXNoZXIy MTI2MTky