GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. 370 SECTION ANCHORING/MOORING Item# Description Size List 241-26524 Standard Grade 81/ 4"L x 5"H w/ 2" holes 37.16 EA 241-26403 Commercial Grade 81/ 4"L x 5"H w/ 21/ 4" holes 55.58 EA D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. D. INSIDE CORNER F. Should be used for all cross supports. F. ANGLE Item# Description Size List 241-26527 Standard Grade Each leg 21/ 2"L x 5"H 11.38 EA 241-26406 Commercial Grade Each leg 21/ 2"L x 5"H 14.50 EA G. Bolts to side of dock to attach fingers and ramps. G. FEMALE T CONNECTOR Item# Description Size List 241-26528 Standard Grade w/ 1/ 2" tabs 5" x 5" 42.59 EA 241-26407 Commercial Grade w/ 1/ 2" tabs 5" x 5" 49.98 EA H. Use with Female T connector to attach fingers and ramps. Bolt set "N" required for joint. H. MALE T CONNECTOR Item# Description Size List 241-26532 Standard Grade w/ 1/ 2" tab 5" x 5" 33.04 EA 241-26408 Commercial Grade w/ 1/ 2" tab 5" x 5" 36.33 EA I. Should be used with every Angle. Two required for each Angle. 11/ 2"L x 5"H. I. WASHER PLATE Item# Description List 241-26409 Commercial Grade 5.02 EA J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/ 4", 3/ 8" and 1/ 2" chain. 5"L x 5"H. J. CHAIN RETAINER Item# Description List 241-26529 Standard Grade 63.68 EA 241-26410 Commercial Grade 80.48 EA K. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set "M" required for attaching. K. PIPE HOLDER/OUTSIDE 3" Item# Description List 241-26411 Commercial Grade 66.95 EA C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. C. OUTSIDE CORNER END Item# Description Size List 241-26523 Standard Grade Each leg is 10"L x 5"H 33.52 EA 241-26402 Commercial Grade Each leg is 10"L x 5"H 48.72 EA P. Used for quick disconnect of male and female connectors. Galvanized 3/ 4" connector pin and hitch clip pin. P. CONNECTOR PIN SET Item# List 241-26531 17.78 EA Q. Reinforcing plates are used to back up single T males and females. 5" x 5". Q. BACK UP PLATE Item# Size List 241-26413 5" x 5" 12.83 EA Item# List 241-26415 421.55 EA Piling hoop & roller intended for areas with a lot of wind, current or tidal action. Combines the Piling hoop (26412) and roller assembly (26414) to make up for the up and down movement. For pilings up to 12" in diameter. Bracket and roller bolt directly to an optional deck plate (26416). S. PILING HOOP AND ROLLER Used to attach A thru K component parts. 3/ 8 x 21/ 2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/ 2" x 3". CARRIAGE BOLT SET Item# Description List 241-26535 Commercial Grade 47.59 BG Item# Description Qty List 241-26431 Commercial Grade 1 pr. 267.75 PK • 5" x 11" x 1/ 4" galvanized steel bracket • Includes left and right ramp brackets INSIDE ROLLING RAMP BRACKET Left side N. Includes lock nut. Used to connect male and female connectors. Galvanized 3/ 4" x 31/ 2". N. HEX HEAD BOLT SET Item# List 241-24279 67.62 BG Has seamless area and UV resistant black polyethylene shell filled with EPS foam. Outer shell resists impacts and protects foam center from saltwater, gasoline and most chemicals. Thick mounting flange can be drilled to accommodate attachment fasteners for easy mounting to any dock design. 8 year floatation warranty. ® DOCK FLOAT Item# Size Max Load List 32-46118v 24" L x 36" W 12" H 335 lbs. 302.19 EA 32-46116v 24" L x 48" W 12" H 450 lbs. 367.59 EA 32-46117v 24" L x 48" W 16" H 600 lbs. 421.49 EA Right side
RkJQdWJsaXNoZXIy MTI2MTky