GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEM NUMBERS IN RED ARE HAZARDOUS ITEMS IN BLUE ARE NEW D SEA VALUE Y OVERSIZED GCOURIER SURCHARGE SECTION 379 ANCHORING/MOORING K. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set "M" required for attaching. K. PIPE HOLDER/OUTSIDE 3" Item# Description List 241-26411 Commercial Grade 69.84 EA N. Includes lock nut. Used to connect male and female connectors. Galvanized 3/ 4" x 31/ 2". N. HEX HEAD BOLT SET Item# List 241-24279 70.54 BG P. Used for quick disconnect of male and female connectors. Galvanized 3/ 4" connector pin and hitch clip pin. P. CONNECTOR PIN SET Item# List 241-26531 18.55 EA Q. Reinforcing plates are used to back up single T males and females. 5" x 5". Q. BACK UP PLATE Item# Size List 241-26413 5" x 5" 13.38 EA Item# List 241-26415 439.75 EA Piling hoop & roller intended for areas with a lot of wind, current or tidal action. Combines the Piling hoop (26412) and roller assembly (26414) to make up for the up and down movement. For pilings up to 12" in diameter. Bracket and roller bolt directly to an optional deck plate (26416). S. PILING HOOP AND ROLLER 1/ 8" hot-dip galvanized steel. 7/ 16" holes for 3/ 8" carriage bolts. Bolts included are stainless steel. Large surface area is used in soft bottom areas. Leg pipe can extend through the pad into lake bottom for extra lateral support. Pointed corners grab when the bottom is rocky. Pipe above pad: 23/ 8" H and pipe below pad: 11/ 2"H STATIONARY DOCK HARDWARE Item# Size Pipe List 686-94102F 11" L x 11" W x 21/ 2" H 21/ 4" ID 50.39 EA Used to attach A thru K component parts. 3/ 8 x 21/ 2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/ 2" x 3". CARRIAGE BOLT SET Item# Description List 241-26535 Commercial Grade 49.64 BG 26522 B. Use with a female outside corner to connect docks end to end. Joint requires 3/ 4" bolt set (N) or connector pin (O). Each leg is 10"L x 5" H. B. OUTSIDE CORNER (MALE) Item# Description Size List 241-26522 Standard Grade 1/ 2" Welded Tab 63.54 EA 241-25491 Commercial Grade 1/ 2" Welded Tab 68.04 EA 26523 C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. C. OUTSIDE CORNER END Item# Description Size List 241-26523 Standard Grade Each leg is 10"L x 5"H 34.97 EA 241-26402 Commercial Grade Each leg is 10"L x 5"H 50.82 EA Item# Description Size List 241-26524 Standard Grade 81/ 4"L x 5"H w/ 2" holes 38.76 EA 241-26403 Commercial Grade 81/ 4"L x 5"H w/ 21/ 4" holes 57.98 EA D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. D. INSIDE CORNER F. Should be used for all cross supports. F. ANGLE Item# Description Size List 241-26527 Standard Grade Each leg 21/ 2"L x 5"H 11.87 EA 241-26406 Commercial Grade Each leg 21/ 2"L x 5"H 15.13 EA G. Bolts to side of dock to attach fingers and ramps. G. FEMALE T CONNECTOR Item# Description Size List 241-26528 Standard Grade w/ 1/ 2" tabs 5" x 5" 44.43 EA 241-26407 Commercial Grade w/ 1/ 2" tabs 5" x 5" 52.14 EA H. Use with Female T connector to attach fingers and ramps. Bolt set "N" required for joint. H. MALE T CONNECTOR Item# Description Size List 241-26532 Standard Grade w/ 1/ 2" tab 5" x 5" 34.47 EA 241-26408 Commercial Grade w/ 1/ 2" tab 5" x 5" 37.90 EA I. Should be used with every Angle. Two required for each Angle. 11/ 2"L x 5"H. I. WASHER PLATE Item# Description List 241-26409 Commercial Grade 5.24 EA J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/ 4", 3/ 8" and 1/ 2" chain. 5"L x 5"H. J. CHAIN RETAINER Item# Description List 241-26529 Standard Grade 66.43 EA 241-26410 Commercial Grade 83.95 EA
RkJQdWJsaXNoZXIy MTI2MTky