GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. 382 SECTION COVERS/TOPS Item# Case List 74-40035 12 14.09 EA Attaches to all Starbrite Extend-A-Brush premium handles to make an adjustable support for covers. Constructed of unbreakable nylon. COVER SUPPORT POLE TIP Item# Length List 32-11991 36" to 64" 73.59 EA These fully adjustable poles now have a cam lock for a more secure means of locking the poles at the desired height. The cam will not scar or mark poles, as other screw type adjusters often do. All poles are satin finish anodized. Includes rubber crutch tip ends. ® BOAT COVER SUPPORT POLE This fully adjustable aluminum support pole is 3 support poles in one. Includes a male canvas snap, grommet tip, and plain end cap with the pole. If you have a female canvas snap or a grommet on your boat cover, you can get a support that will work with your cover. A durable plastic adjuster sets the correct height for your cover. ® 3-IN-1 SUPER SUPPORT POLE Item# Length List 32-11992 36"-64" 108.29 EA Don't let your interior suffer from mold and mildew damage. Proper ventilation can keep these boat destroying fungi from attacking your boat! Installs quickly and easily, with no screws or fasteners. The venting area provides for greater volume of exhaust air while closing the top to bottom gap - keeping water out! The Boat Vent II is manufactured from a superior grade poly carbonate blend material for strength and UV resistance and will accommodate either 3/ 4" or 7/ 8" support poles. ® BOAT VENT II Item# List 32-11982 53.99 EA Item# List 500-VENTII 42.19 EA Add to any custom or styled-to-fit boat cover. Made with UV inhibited polymers to withstand the elements. Helps prevents mold, mildew, and bacteria from growing under the boat cover and causing irreversible damage to the boat’s interior. Can be used alone or with most standard 3/ 4" support poles. BOAT VENT II • Helps prevent water from pooling in low places on boat cover and helps maintain the quality of your boat cover • Comes with (3) supports, (2) 33’ straps with hooks and a bonus boat hook • Fits most pontoon boats with up to 33' deck length An easy-to-use telescoping support system that keeps your cover from sagging and allowing water to pool, helping extend the life of the material. The (3) supports are self-standing with support plates on the tops and bottoms. The bottom support plates have foam pads to protect the boat and prevent shifting. Adjust height easily from 30" to 50" in 2.5" increments and it contains two straps with durable hooks. Each polyester strap assembly is 33'-34' long. Easy to install and stores compactly when not in use. PONTOON BOAT COVER SUPPORT Item# List 117-41971 211.99 EA Item# List 32-55741 105.59 EA Helps extend the life of your boat cover by preventing water from pocketing. Includes 50' of webbing, quick release buckles, a boat cover support pole that snaps to the webbing, and two hooks to attach to the transom. ® BOAT COVER SUPPORT SYSTEM Item# Length List 500-60002 22" to 70" 81.19 EA The innovative vent assembly allows any boat cover to vent to help prevent mold and mildew inside the boat. Includes an anodized aluminum telescoping pole, vent, and instructions. BOAT COVER SUPPORT POLE WITH VENT Item# Length Case List 50-97301] 35" to 64" 12 55.86 EA 1" Anodized aluminum construction. Supplied with mushroom top, snap-on fastener top and rubber cap. TELESCOPING BOAT COVER SUPPORT POLE WITH BASE Shown w/ Mushroom Top Item# Length List 23-107045 28"-48" 43.99 EA 23-107055 36"-64" 47.39 EA 1" Anodized aluminum pole telescopes quickly and easily to raise the cover and allow water to drain off. Locks and unlocks with a twist. Includes rubber caps at both ends. BOAT COVER SUPPORT POLE Item# Description List 354-4911101 61/ 2" Cover Support Crown 19.99 EA 354-4911151 Strap Kit Only (w/3ea 15' Straps) 54.69 EA An injection molded nylon crown that fits the tip of an adjustable boat hook or any universal/Acme thread. Optional Webbing Straps are used for positioning the Support Crown securely in place. 4911151 Includes: Three 15' straps, with a securing loop on one end and an adjustable snap clip on the other. BOAT HOOK MOORING COVER SUPPORT CROWN
RkJQdWJsaXNoZXIy MTI2MTky