GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. 682 SECTION ELECTRICAL Item# Volts List 661-7620 12V DC 463.36 EA 661-7622 12VDC w/ manual override 589.48 EA 661-7623 24V DC w/ manual override 491.22 EA Opt. Accy. Description List 661-9160 Paralleling link bus 43.80 EA 500 Amp magnetic latching (bi-stable) relay automatically combines batteries during charging and isolates batteries when discharging and when starting engine. Start Isolation (SI) can be configured for temporary isolation of House loads from Engine circuit during engine cranking. Engine Isolation (EI) can be configured for isolation of two engines while both are running to maximize alternator output. Manual override knob provides an added level of safety. • Draws very low current in the ON state • Senses charging on two battery banks • Label recesses for circuit identification • Silver alloy contacts provide high reliability • Includes Remote Control Contura Switch (2146) ML SERIES AUTOMATIC CHARGING RELAY Item# Amps Application Volts List 12-48070BX 70 1 Alternator/2 Batteries 12-36 158.66 EA 12-48090 90 1 Alternator/2 Batteries 12-36 179.62 EA 12-48120 200 1 Alternator/2 Batteries 12-36 291.24 EA For 12-36 volt, DC negative ground electrical systems. Isolate each battery to prevent the battery with the higher charge from draining into the battery with the lower charge. Allow two batteries to be charged simultaneously from a single power source. • Amp rating per leg, 2 legs • Three 1/ 4" stud terminals, 61/ 2 L x 31/ 4" W x 213/ 6" H HEAVY DUTY BATTERY ISOLATOR Item# Description Banks List 469-83116025 1602 IG 2 649.26 EA The ultimate solution for charging several batteries simultaneously. Compatible with any type of alternator/battery charger, in both existing and new systems. Performs far better than conventional battery isolators. This ensures fast and complete charging of your batteries without having to make additional adjustments to the alternator. Its components compensate for variations in voltage and ensure that charging continues at the right voltage level, even with several battery banks. The input side is connected to the alternator and/or battery charger, while two batteries are connected to the output side. Easy to install on a DIN rail (industry standard). BATTERY ISOLATORS MATE IG Item# Amps Description List 175-01702 70 1 alternator/2 batteries 182.54 EA 175-01703 70 1 alternator/ 3 batteries 227.40 EA 175-2702 70 2 alternators/2 batteries 386.69 EA 175-02703 70 2 alternators/3 batteries 340.48 EA 175-11302 130 1 alternators/2 batteries 335.89 EA 175-11303 130 1 alternators/3 batteries 435.20 EA 175-21302 130 2 alternators/2 batteries 642.58 EA 175-21303 130 2 alternators/3 batteries 861.75 EA Operates on 6, 12, 24 and 32 volt negative ground systems. Allows electrical current to flow from DC source to batteries in one direction only. This allows device to charge multiple battery banks without the banks being connected. NOTE: all isolators impose a .6 volt drop in the circuit. BATTERY ISOLATOR Item# Amps Banks Volts Size List 175-23121 120A 2 12 5.35" L x 5.875" W x 3.125" H 273.92 EA 175-23125 180A 3 12 7.55" L x 5.875" W x 3.125" H 497.37 EA 175-23127 130A 4 12 12.05" L x 5.875" W x 3.125" H 470.59 EA Pro IsoCharge delivers digitally controlled alternator output distribution while protecting the health of engine start batteries. Eliminate typical alternator voltage loss of up to .6VDC that is commonly associated with traditional diode based isolators. Intelligent zero volt loss isolation ensures fully charged batteries and faster charging times. Installed with the ProNautic P Series chargers, a boat owner can enjoy the full benefit of shore power and on the water charging. PRO ISOCHARGE Item# Amps Volts Size List 354-4227901 140 12 25/ 8" x 25/ 8" x 2" 109.23 EA Allows two batteries to automatically charge at the same time and then isolates the batteries, ensuring the starting battery is always charged. Automatically engages or disengages the circuit at pre-set voltages, eliminating the possibility of discharging the primary starting battery. Cut-in voltage: 13.3V. Cut-out voltage: 12.8V. Surge protected. An LED indicator alerts the user when the unit is engaged. Constructed of machined brass with a weatherproof injection molded nylon housing and silver tipped contacts. Includes two #8 RH fasteners. IP65 rating. SMART DUAL BATTERY ISOLATOR Battery isolators allow you to charge multiple batteries from a single source. * Will not work with Delco "CS" style alternators. Item# Amps Application List 47-6855 75 1 alternator / 2 batteries* 166.69 EA BATTERY ISOLATORS Item# List 11-BS11040 119.33 EA • Automatically combines two batteries when charging and isolates the two batteries when not charging • Nominal Voltage: 12VDC • 125A Continuous • 140A Intermittent • No voltage drops like battery isolators (0.6V) • Robust Glass Fiber nylon enclosure • LED indication when VSR is engaged • Port for remote status LED • Surface or panel mount options • Power Consumption: 10mA (Standby)/ 330mA (Engage), 0mA (Storage Mode) • Zero power consumption when the engine is off • CE and IP67 Certifications VOLTAGE SENSITIVE RELAY Item# Size List 262-82012301 11/ 4" D x 41/ 2" W x 51/ 2" H 360.51 EA Charges auxiliary or starting batteries from your inverter/ charger with limited voltage drop • 15 A maximum charge current, automatically adjusts for 12 or 24 volt battery banks, automatically switches on/off without affecting the battery bank or over-charging • Other features include built-in thermal and over-current protection, reverse polarity protection and easy three wire installation ECHO-CHARGE AUXILIARY BATTERY CHARGER • Twin or Triple engine configurations • Remotely operated switches via analog inputs or CZone® • Configurable dual direction voltage sensitive switches • Monitors and transmits all battery voltages, including house bank state of charge over NMEA2000 for integration with multi-function displays • 2 x additional sensor inputs • Full mechanical override of all switches for safety and servicing • Parallel two units together for 4, 5 or 6 engine installations A complete battery management system for 2 - 6 outboards. Simplifies battery management with remotely activated switches, automatic Voltage Sensitive Switching (VSS) and emergency parallel functionality in a robust, easy-to-install, ignitionprotected IPX7 enclosure. SMART BATTERY HUB Open Item# Description List 969-80716003000 Twin Engine 2537.49 EA 969-80716003100 Triple Engine 3044.99 EA Opt. Accy. Description List 969-80716003200 Smart Battery Hub Temp Sensor (15m) 100.04 EA
RkJQdWJsaXNoZXIy MTI2MTky