GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEM NUMBERS IN RED ARE HAZARDOUS ITEMS IN BLUE ARE NEW ] SEA VALUE v OVERSIZED dCOURIER SURCHARGE SECTION 861 FASTENERS Weld Mount Fastening System Stainless stud mounts to virtually any surface using our acrylic adhesive. This is a structural part with 500 lbs of tensile strength and 650 lbs shear strength. Can be bonded from either surface of the base plate. STAINLESS STEEL THREADED STUDS Item# Size Qty Case List 817-83212100 8-32 x 3/ 4" 1 100 5.89 EA 817-83224100 8-32 x 11/ 2" 1 100 7.29 EA 817-S102412100 10-24 x 3/ 4" 1 100 8.69 EA 817-ST125102416100 10-24 x 1" 100 1 529.39 EA 817-102420100 10-24 x 11/ 4" 1 100 9.99 EA 817-102424100 10-24 x 11/ 2" 1 100 9.99 EA 817-142012100 1/4-20 x 3/ 4" 1 100 7.29 EA 817-142016100 1/4-20 x 1" 1 100 8.99 EA 817-142020100 1/4-20 X 11/ 4" 1 100 10.19 EA 817-S142024100 1/4-20 x 11/ 2" 1 100 9.89 EA 817-142032100 1/4-20 x 2" 1 100 14.29 EA 817-S142040100 1/4-20 x 21/ 2" 1 100 15.79 EA 304 Stainless steel female threaded standoff mounts to virtually any surface. Can be bonded to either the upper or lower base surface. Use for through deck mounting of hardware or anywhere you need a fixed female thread. Maximum torque load is 90 in/ lbs. .75" H x 1.25" Dia. BLIND THREADED STANDOFF Item# Size List 817-S14201230425 1/ 4"-20 22.89 EA Item# Size Qty List 817-901024 10-24 10 147.39 PK 817-901420 1/4-20 10 144.89 PK Designed for thru hole and blind mounting applications. The rubber fixture holds the part in place while it is bonded in place. The fixture keeps the threads clean during installation. The threaded nut floats allow for accurate bolt alignment. Nut plates eliminate tapping saving significant labor costs. FLOATING NUT PLATES Item# Color Qty List 817-803950BK Black 50 60.59 PK 817-803900BK Black 100 96.79 PK 817-803950 White 50 60.59 PK Black White For panel and other small space applications. Molded mount is sized for a 3/ 16" wide wire tie with a maximum width of .20". Average pull strength is about 50 lbs. and measures .44" square. Use for runs with only a few wires or in limited space. Excellent for mounting compass wires on center console boats and for overhead panel runs. AT-3 SMALL NYLON WIRE TIE MOUNT Item# Color Qty List 817-805950BK Black 50 72.69 PK 817-805900BK Black 100 119.89 PK 817-805950 White 50 71.59 PK Black White Set into wet resin during the hull lay up or bonded with our acrylic adhesives. Designed for a 3/ 8" wide wire tie and has an average pull strength of 150 lbs. Approved for submerged bilge applications. No need for plywood in the hull just to have a place to drive wire tie screws. Saves material and labor costs! AT-5 LARGE NYLON WIRE TIE MOUNT Item# Fits Size List 817-808100 Ties up to 0.35" W Small, AT-8 3.79 EA 817-809100 Ties up to 0.40" W Large, AT-9 4.19 EA Use with Stainless Steel or Nylon wire ties. High tensile strength when bonded with AT-6030 adhesive. Manufactured of 5052 marine grade aluminum for UV and salt water resistance. Ideal alternative to welding or drilling and tapping to mount hoses, conduit, etc. ALUMINUM WIRE TIE MOUNT Item# Qty Case List 817-807100 1 100 7.19 EA An anodized aluminum base with a nylon tie mount riveted to the base. The nylon mount swivels 360°, making alignment with the wire harness easier. Designed for a #5 wire tie and has an average pull strength of 150 Lbs. AT-7 ALUMINUM BASE WIRE TIE MOUNT Each mount is designed to be mounted using 1/ 4"x20 Weld Mount studs (sold separately). Polypropylene clamps are temperature rated for -22°F to +194°F continuous service. Shown with Required Stud (Sold Separately). CABLE AND HOSE CLAMP MOUNTS Item# Description Size Color Stud Qty List Double Clamp 817-801000 Double 1" Black 142028100 (Required) 25 8.79 PK Item# Size Color Qty List 817-8011325 3.25" L X 1" W White 25 150.69 PK Designed to be bonded with AT-2010 or AT-4020 acrylic adhesive. Holds up to a 1.3" strap width. Incredibly strong, rated for over 300 lbs in tensile and it's paintable. Use it for battery and tank tie downs and mounting heavy hoses and cables or deck mounted for life raft tie downs. AT-113 FOOTMAN’S STRAP MOUNT Item# Description List 817-803001 Gun 157.39 EA 817-S008013 10:1 Plunger for AT-6030 (2016+) 28.59 EA 817-008014 1:1 Plunger for AT-2010/4020/8040 28.59 EA The AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10:1 plunger). Replacement plungers are also available. Dries gold. AT-300 ADHESIVE DISPENSING GUN Item# Description Size Qty List 817-008040 AT-8040 Bonder 50ml 1 75.89 EA 817-80850 AT-850 mixing tips 10 35.19 PK 817-8085050 AT-850 mixing tips 50 159.49 PK A solvent free, VOC Compliant, 2-part methacrylate-based, structural adhesive formulated to bond metals for use in severe environments. It will also bond engineered thermo and thermosetting plastics, composites to metals or various substrate combinations. It has excellent adhesion to metal surfaces including aluminum, stainless steel, galvanized steel, and plated steels. Forms a tough, high strength bond usually with minimal surface preparation. Ultimate strength exceeds 3500 psi of tensile shear strength on aluminum with remarkable impact and peel strengths. Holds all Weld Mount parts on a vertical or overhead surface without sagging when properly used. AT-8040 NO SLIDE MULTI BONDER Item# Description Qty List 817-02010 AT-2010 Adhesive 1 75.89 EA 817-S805002 Dual pusher rod 10 43.99 PK A unique 1:1 adhesive. It has high viscosity and cures in 5 - 6 minutes with a 4 minute working or open time. This makes AT-2010 the ideal adhesive for applications which require an immediate high strength bond. AT-2010 has a 12 month shelf life when stored at 72°F or less. Packaged In a 50 ml cartridge which will bond 150 - 200 parts. Dries brown. AT-2010 6 MINUTE ADHESIVE
RkJQdWJsaXNoZXIy MTI2MTky